PM Series
•
PM-10
2-Way, 10"
High Power System
|
|
Characteristics
|
 |
Multi-angled unit, designed for Sound reinforcement or floor
monitoring. |
|
Multi-use Mid-High Constant Directivity,
rotateable 90x45 degrees Horn. |
|
Active driver "Power Guard" protection without any effective loss. |
|
High Sound Pressure Level,
(128dB Peak@1m, pink noise with a 6dB crest-factor). |
|
Rotating Horn and
optimised cabinet architecture for monitoring and small P.A. uses. |
|
Two-way passive 8 Ohm design to be used with a single power Amp channel per cabinet to obtain an easy assembly and low cost. |
|
Passive filter, which
optimises the voice critical zone response. |
|
Double input NL-4
Neutrik connector permitting parallel bridging. |
|
Steel front grille with acoustic foam, easily removable, held in place with powerful Neodymium magnets. |
|
Suspension Tracks on top bottom, standard pole cup and
inserted threads. |
|
The specific electronic controller guarantees: linear performance, Powerful bass response, and reliability.
|
| Applications |
|
|
Touring, installed P.A., theatres, multi-purpose rooms, etc. |
|
High performance Monitoring |
|
When used together with the series' Sub-woofer
PMS-15, the system becomes a performing set-up for many dance applications.
|
| Specifications and Characteristics |
| Frequency Response (Hz)1 |
±3dB
60Hz - 18KHz |
| Frequency Range (Hz)1 |
±10dB
40Hz - 20KHz |
| Nominal Impedance |
8 Ohm |
| Power Rating |
|
| (RMS)2 |
300W |
| Program2 |
600W |
| Peak2 |
1200W |
| Horizontal Coverage |
(-6dB) 90º |
| Vertical Coverage |
(-6dB) 40º |
| Sensitivity
(dB/1w@1m) |
97dB SPL |
| SPL Max./Peak (dB
SPL@1m)3 |
128dB SPL |
| Connectors |
2
Neutrik NL-4 Connectors on steel plate |
| Recommended Signal Processor |
RAM Audio LMS-244 Digital Processor
|
| Recommended Power Amp |
250W / 500W @ 8 Ohm, 1
PM-10 / channel
|
| Recommended Sub-woofer |
Space
PMS-15 |
| Enclosure and Installation |
| Enclosure |
Vertical, multi-angle 15mm Baltic cross-ply construction, tongue and groove assembly throughout.
Bi-component epoxy finish. |
| Components |
1x10"
300W AES 3" coil
Driver 2" coil 70W AES |
| Protection Grille |
1.5mm
laminated steel with textured epoxy finish. |
| Handle |
On top of the cabinet. |
| Dimensions
(WxDxH) |
324
x 294 x 521 mm
12.8 x 11.6 x 20.5 inches |
| Net Weight |
18Kg (39.6
pounds) |
| Rigging |
Integrated Track Rigging System on top and bottom.
M-6 Inserts for bolt assembly. |
|
| Notes |
|
1
Specifications in half space
2
With filtered Pink Noise 6dB crest-factor
3
Calculated from the Sensitivity and Power Data |
|
|
|
Download pdf info file |
|
|
The PM-10 Unit is a compact system, offering high Sound Pressure levels in a small footprint.
It has been designed as a two-way passive system, in a multi-angled cabinet, performing as well as a floor monitor or as a small P.A. system. Equipped with a Constant -
Directivity Mid-High Horn, it possesses a simple yet effective way to rotate it, in order to be in the right position when used vertically, (P.A.) or horizontally, (Floor Monitor).
As a P.A. reinforcement unit it can be mounted on a stand, suspended via its built-in tracks or some of its
several inserted M-6 threads.
As a floor monitor, it will cover several distances in many different uses thanks to its various angles setting possibilities.
Its dimensions, aiming capacity and coverage have been combined to
optimise the performance in each possible use.
Together with the different working angles and the rotating
Horn, the passive filter has been developed to achieve an optimum performance in the range of the vocal spectrum, offering at the same time an effective feed-back control.
The PM-10 can be used on its own without any electronics processing, but has been conceived right from the start and following the current tendencies, to obtain its full musical expression capabilities, through the use of a specific signal processor. Thus, the PM-10 is able to reproduce the deepest bass with utmost purity, expression and reliability.
|
